More Details

 

Just how do you feel in regards to A Step-by-Step Guide to Installing a Bathtub?

Mounting a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a moderately challenging project. If the old tub is conveniently accessible, the task can relocate immediately; if you have to open up a wall to remove the old bathtub and also place the brand-new bath tub, the job is much harder. In either case, the project is within a residence handyman's skills, although you will require an assistant to leave the old tub as well as set in the brand-new one. See to it you have actually qualified yourself for the work and fit attempting it. As opposed to employing a contractor to take control of a halfway-completed task, it is far better to think about using one prior to you start. Possibilities are you might require a professional plumber to make tube connections.
This post will certainly help you install a new tub in your washroom if you have already purchased a new bathtub as well as don't need to transform the plan of your previous water system pipes.
Your devices as well as material list ought to consist of the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Getting ready for the Installment

To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its final placement.

 

 

Removing Old Taps

If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The procedure of removing the existing taps can be fairly problematic as a result of the restricted accessibility that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

 

 

Mounting the Bathtub

Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To set up taps, fit the bottom of the outermost flexible faucet adapter to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Switch on the water supply and also examine all joints and brand-new pipework for leaks and tighten them if required. Load the bath tub as well as likewise check the overflow outlet and also the regular outlet for leaks.
Ultimately, fix the bathroom paneling as described in the supplier's instruction manual. Tiling as well as sealing around the bathtub needs to wait up until the bath tub has actually been utilized at least once as this will certainly settle it into its last placement.

 

 

Fitting New Touches

If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the tap in place with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be connected to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bath tub

In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a rigid seal, triggering the water to pass through the wall in between the bathroom and the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and installations. They are marketed in tubes as well as cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to enable the activity experienced when the bathtub is in usage. The sealer can break relatively very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water-proof sticky as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you appreciate more info about A Step-by-Step Guide to Installing a Bathtub? Give a review below. We would be pleased to know your views about this blog posting. In hopes that you visit us again in the near future. Feel free to take a moment to share this entry if you enjoyed reading it. We appreciate reading our article about How to Install a Bathtub.

Leading emergency plumbing services available.